This is the Quarter 1, Module 5 self-learning module for TLE Shielded Metal Arc Welding (SMAW), Grade 7/8, titled “Interpret Plans and Drawings (ID).” It is part of an exploratory course that leads to the SMAW National Certificate Level II (NC II). After working through it, learners should be able to read the welding symbols on a technical drawing and use them to choose the right materials, tools, and equipment.
The module was published in 2020 (First Edition) by the Department of Education, SOCCSKSARGEN Region, as an Alternative Delivery Mode (ADM) material. It was written by Neil C. Maaya.
On this page 7 sections
What learners will learn
The module covers two common competencies:
- Analyze signs, symbols and data (TLE_IAAW7/8ID-0i-j-1)
- Interpret technical drawing (TLE_IAAW7/8ID-0i-j-2)
By the end of the lesson, learners are expected to:
- Determine appropriate welding materials based on a technical drawing
- Identify tools, materials, and equipment according to plans
The four main parts of an arc welding symbol
The module explains that every arc welding symbol has four main parts:
- Reference line: the line connected to the arrow. Whether the basic symbol sits above or below this line tells where the weld goes. It is always drawn parallel to the bottom edge of the drawing or the base line of a view.
- Arrow: shows the position of the weld. It is drawn at an angle from the end of the reference line to one side of the joint, called the arrow side. The opposite side is the other side of the joint.
- Basic weld symbol: describes the type of weld. It is a small drawing of how the metal’s edge is prepared before welding.
- Tail: added only when special notes are needed. A number or letter code inside the tail points the welder to notes elsewhere on the drawing, such as heat treatment or the welding process.
Where the weld goes
- Weld symbol below the reference line: weld on the arrow side of the joint.
- Weld symbol above the reference line: weld on the other side of the joint.
- Weld symbols above and below the line: weld on both sides.
Basic weld symbols
The module shows the symbols for fillet, plug, spot, seam, backing, melt-thru, surfacing, and flange edge welds, along with groove shapes such as square, V, bevel, U, J, flare V, flare bevel, and flange corner.
Letters and dimensions on a welding symbol
A welding symbol can also carry dimensions, such as the length, width, and height of the weld, the root opening, and the angle. The module lists these letters:
| Letter | Meaning |
|---|---|
| F | Finish symbol |
| A | Groove angle |
| R | Root opening |
| S | Depth of bevel |
| E | Groove weld size |
| L | Length of weld |
| P | Pitch of weld (center-to-center spacing) |
| T | Tail of weld |
| N | Number of spot or projection welds |
Supplementary, contour, and finish symbols
Supplementary symbols can be placed above or below the basic symbol, or where the reference line meets the arrow.
- Weld all around: a circle on the welding symbol, meaning the weld goes all around the part.
- Field weld: a flag symbol, meaning the weld is made at the job site (“in the field”) instead of in a fabricating shop.
- Melt through: complete joint penetration for a joint welded from one side, with visible root reinforcement.
- Backing: an open rectangular box used with a groove weld symbol on the reference line, showing that material is needed on the opposite side to control penetration.
- Spacer: an open box that crosses the reference line, showing that a spacer is placed between the joint.
Contour symbols tell the shape of the finished weld surface:
- Flush: the weld should be about flat with the surface.
- Convex: the weld should be raised.
- Concave: the weld should curve inward.
If the contour needs finishing, a finishing symbol is added with a letter: G for grinding, C for chipping (spelled “shipping” in the module), M for machining, and U for unspecified.
How to use this module
The module follows the usual self-learning module parts:
- What I Know: a 15-item multiple-choice pretest.
- What’s In: a review of the past lesson, where learners list five practices in preventive maintenance of SMAW tools.
- What’s New and What is It: learners identify symbols on a sample drawing and answer guide questions, then read the discussion of welding symbols.
- What’s More: identify and draw five described symbols.
- What I Have Learned: identify five given symbols.
- What I Can Do: sketch a 4×4 table, 2 ft high, using welding symbols, and list at least five tools needed to make it.
- Post-Test and Additional Activities: a 15-item post-test, then analysis of a fillet weld sketch with plan and elevation views.
For learners: Write all answers on a separate sheet of paper, not on the module. Use the answer key at the end honestly to check your work.
For parents: Help your child read the instructions before each task, and remind them to contact the teacher when a task is unclear.
For teachers: The module includes Notes to the Teacher and an answer key for the pretest, post-test, What’s More, and What I Have Learned.
Frequently asked questions
What grade and quarter is this SMAW module for?
It is for TLE SMAW Grade 7/8, Quarter 1, Module 5, as shown by the code CO_Q1_TLE-SMAW 7/8 Module 5.
What are the four main parts of an arc welding symbol?
The reference line, the arrow, the basic weld symbol, and the tail. The tail is added only when special notes are needed.
What does the field weld symbol mean?
It is a flag added to the welding symbol to show that the weld is made at the job site, or in the field, rather than in a fabricating shop.
Does the module have an answer key?
Yes. It has answers for the pretest, the post-test (labeled Assessment), What’s More, and What I Have Learned.
What do the letters F, A, and P mean on a welding symbol?
F stands for the finish symbol, A for the groove angle, and P for the pitch of the weld, which is the center-to-center spacing of welds.
Full text of the module
The text below is a transcription of the PDF above, as printed.
TLE (SMAW) Module 5: Interpret Plans and Drawings (ID)
[illustration: students reading and studying under a tree, at a desk with a teacher, and with a globe and a lamp]
CO_Q1_TLE-SMAW 7/8_ Module 5
TLE SMAW – Grade 7/8
Alternative Delivery Mode
Module 5: Interpret Plans and Drawings (ID)
First Edition, 2020
Republic Act 8293, section 176 states that: No copyright shall subsist in any work of the Government of the Philippines. However, prior approval of the government agency or office wherein the work is created shall be necessary for exploitation of such work for profit. Such agency or office may, among other things, impose as a condition the payment of royalties.
Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names, trademarks, etc.) included in this module are owned by their respective copyright holders. Every effort has been exerted to locate and seek permission to use these materials from their respective copyright owners. The publisher and authors do not represent nor claim ownership over them.
Published by the Department of Education Secretary: Leonor Magtolis Briones Undersecretary: Diosdado M. San Antonio
Development Team of the Module
Writers: Neil C. Maaya
Editors: Jose Joel B. Moso, Isidro L. Dagum, Jr.
Reviewers: Evelyn C. Frusa PhD, Grace J. Miravalles, Rolex H. Lotilla and Arvin Tejada
Illustrator: John Lester B. Escalera
Layout Artist: John Lester B. Escalera
Management Team: Allan G. Farnazo, CESO IV – Regional Director
Gilbert B. Barrera – Chief, CLMD
Arturo D. Tingson Jr. – REPS, LRMS
Peter Van C. Ang-ug – REPS – ADM Coordinator
Belen Fajemolin, Ph.D. – CID Chief
Evelyn C. Frusa, Ph.D – EPS In Charge of LRMS
Bernardita M. Villano – ADM Coordinator
Printed in the Philippines by Department of Education – SOCCSKSARGEN Region
Office Address: Regional Center, Brgy. Carpenter Hill, City of Koronadal
Telefax: (083) 2288825/ (083) 2281893
E-mail Address: region12@deped.gov.ph
Introductory Message
This Self-Learning Module (SLM) is prepared so that you, our dear learners, can continue your studies and learn while at home. Activities, questions, directions, exercises, and discussions are carefully stated for you to understand each lesson.
Each SLM is composed of different parts. Each part shall guide you step-by- step as you discover and understand the lesson prepared for you.
Pre-test are provided to measure your prior knowledge on lessons in each SLM. This will tell you if you need to proceed on completing this module, or if you need to ask your facilitator or your teacher’s assistance for better understanding of the lesson. At the end of each module, you need to answer the post-test to self-check your learning. Answer keys are provided for each activity and test. We trust that you will be honest in using these.
In addition to the material in the main text, Notes to the Teachers are also provided to the facilitators and parents for strategies and reminders on how they can best help you on your home-based learning.
Please use this module with care. Do not put unnecessary marks on any part of this SLM. Use a separate sheet of paper in answering the exercises and tests. Read the instructions carefully before performing each task.
If you have any questions in using this SLM or any difficulty in answering the tasks in this module, do not hesitate to consult your teacher or facilitator.
Thank you.
What I Need to Know
Welcome to the world of Shielded Metal Arc Welding (SMAW). This Module is an exploratory course which leads you to Shielded Metal Arc Welding [SMAW] National Certificate Level II [NC II]. It covers common competencies for you to possess. These competencies are;
- Analyze signs, symbol and data: TLE_IAAW7/8ID-0i-j-1
- Interpret technical drawing: TLE_IAAW7/8ID-0i-j-2
Learning Objectives
At the end of the lesson, you are expected to do the following:
- Determine appropriate welding materials based on technical drawing
- Identify tools, materials and equipment according to plans
What I Know
Pretest
A. Multiple Choice Write the letter of the correct answer on your answer sheet.
What is the symbol for Site Weld?
a. [illustration: open circle] b. [illustration: horizontal line] c. [illustration: arch] d. [illustration: filled circle]What is the symbol for Site Weld around?
a. [illustration: open circle] b. [illustration: horizontal line] c. [illustration: arch] d. [illustration: filled circle]What is the symbol for Site Flush Contour?
a. [illustration: open circle] b. [illustration: horizontal line] c. [illustration: arch] d. [illustration: filled circle]What is the symbol for Site Concave Contour?
a. [illustration: open circle] b. [illustration: horizontal line] c. [illustration: arch] d. [illustration: curved hook]What is the symbol for Site Convex Contour?
a. [illustration: open circle] b. [illustration: horizontal line] c. [illustration: arch] d. [illustration: curved hook]What does symbol F represents?
a. Groove Angle c. Length of Weld
b. Finish d. Pitch of WeldWhat does symbol P represents?
a. Groove Angle c. Length of Weld
b. Finish d. Pitch of WeldWhat does symbol A represents?
a. Groove Angle c. Length of Weld
b. Finish d. Pitch of WeldWhich is not a part of ARC welding symbol?
a. A reference line c. A round
b. An arrow d. A tailIt is a circle drawn on the welding symbol, indicating that the described weld is to be made all around the part.
a. Weld all round c. Field cut
b. Field weld d. CircleIt is located on the side as the symbol and indicates that the weld should be raised or convex shape.
a. Convex contour symbol c. All round
b. Concave contour symbol d. Site weldIt is a line connected to the arrow.
a. Reference line c. Tail
b. arrow d. Basic wield symbolIt indicates the position of the weld.
a. Reference line c. Tail
b. arrow d. Basic wield symbolIt is added to the symbol when a special note is required.
a. Reference line c. Arrow
b. Tail d. Basic wield symbolIt is an open box that intersects the reference line
a. Spacer c. Flush contour
b. Backing d. Concave contour
Interpret Plans and Drawings (ID)
What’s In
Review of Past Lesson
Preventive maintenance of tools is necessary to avoid injuries in the work place. Give at least Five (5) practices in Preventive Maintenance of Tools in SMAW.
Metal works are essential to the industry specially in building construction, household equipment’s and even in the learning environment. In other areas of specialization, you have signs and symbols in order to work properly and guided. In shielded metal arc welding (SMAW) you need to understand this symbols in order to complete a job clearly and understood what is the objective of the given work.
Did you have sketches of metal works at home or in the machine shop? Can you identify those symbols used? I think you should know, because in creating metal works you need to understand these technical e drawings and symbols to work correctly.
[illustration: hand holding papers]
Notes to the Teacher
- Read the lessons properly. These will guide you to do at the end of this module.
- Find out what you already know by taking the learning activities.
- Apply what you have learned in another activity or real life situation.
What’s New
[illustration: hand holding a sprouting leaf]
[illustration: drawing of a metal block with weld symbols above the joint and a vertical plate, showing basic welding symbols]
These drawing uses technical signs and symbol representing basic welding process. Can you identify some of the symbols used in this drawing. Write it in your answer sheet.
What is It
[illustration: magnifying glass]
Guide Questions: Answer the following questions and write your answer in your activity notebook.
Give 5 examples of symbols you use in drawing plans.
What do you think of the importance of the interpreting drawing in metal work?
Welding Symbol
Welding symbol have specific role in the standards of welding with respect to each roles of the symbol.
The arrows in a welding symbol represents the other side of the weld.
Some weld symbols have no arrow or other side significance. Though, supplementary symbols used in conjunction may have such significance.
References: these are needed to clarify a symbol; the reference is positioned in a tail on the welding symbol.
Dimensions: represents the length, width and height of the weld, root opening and angle.
Use of Welding Symbols
[chart: diagram; Use of Welding Symbols]
Labels printed in the diagram:
- FINISH SYMBOL
- CONTOUR SYMBOL
- ROOT OPENING; DEPTH OF FILLING FOR PLUG AND SLOT WELDS
- EFFECTIVE GROOVE WELD SIZE
- DEPTH OR PREPARATION; SIZE OR STRENGTH FOR CERTAIN WELDS
- SPECIFICATION, PROCESS, OR OTHER REFERENCE
- TAIL
- (TAIL OMITTED WHEN REFERENCE IS NOT USED)
- BASIC WELD SYMBOL OR DETAIL REFERENCE
- ELEMENTS IN THIS AREA REMAIN AS SHOWN WHEN TAIL AND ARROW ARE REVERSED
- GROOVE ANGLE; INCLUDED ANGLE OF COUNTERSINK FOR PLUG WELDS
- LENGTH OF WELD
- PITCH (CENTER-TO-CENTER SPACING) OF WELDS
- FIELD WELD SYMBOL
- ARROW CONNECTING REFERENCE LINE TO ARROW SIDE MEMBER OF JOINT
- WELD-ALL-AROUND SYMBOL
- REFERENCE LINE
- (OTHER SIDE)
- (ARROW SIDE)
- (BOTH SIDES)
- (BOTH)
- NUMBER OF SPOT OR PROJECTION WELDS
- Letters shown: F, A, R, S, E, L, P, T, N
Values are not labeled on the chart.
Source of Image: https://weldguru.com/wp-content/uploads/welding-symbol-fig3-2.gif
- F – Finish Symbol
- A – Groove Angle
- R – Root Opening
- S – Depth of Bevel
- E – Groove Weld Size
- L – Length of Weld
- P – Pitch of Weld
- T – Tail of Weld
- N – Number of Spot or Projection Welds
- [illustration: field weld flag symbol] – Field Weld
- [illustration: open circle] – Weld All Around
- [illustration: horizontal bar] – Contour Symbol
CO_Q1_TLE-SMAW 7/8_ Module 5
Meaning and Uses of symbols
Four main parts of Arc Welding Symbols
- A reference line
- An arrow
- A basic welding symbol
- A tail
[chart: diagram; labeled figure of the four parts of an arc welding symbol] Labels printed on the diagram: REFERENCE LINE, ARROW, BASIC WELD SYMBOL, TAIL
- The reference line is a line connected to the arrow. The position of the basic symbol above or beneath this line determines the location of the weld. The reference line is always drawn parallel to the bottom edge of the drawing, or to the base line of a view.
[illustration: reference line with arrow above two adjoining rectangles] Printed label: REFERENCE LINE
- The arrow indicates the position of the weld; it is drawn at an angle from the end of the reference line to one side of the joint. This side is called the „arrow side of the joint‟. The opposite side is called the other side of the joint.
[illustration: joint diagram with arrow pointing to the arrow side of the joint] Printed labels: OTHER SIDE OF JOINT, ARROW, ARROW SIDE OF JOINT
Welds on the “arrow side of the joint‟ are shown by inverting the weld symbol and placing it beneath the reference line.
[illustration: joint with arrow and reference line, showing a fillet weld symbol beneath the reference line] Printed labels: ARROW, REFERENCE LINE, BASIC WELD SYMBOL
Symbol Indicating Fillet Weld at Arrow Side of Joint
- Welds on the “other side of the joint‟ are shown by placing the symbols above the reference line.
[illustration: joint with arrow and reference line, showing a fillet weld symbol above the reference line] Printed label: BASIC WELD SYMBOL
Symbol indicating fillet welds on the other side of joint.
- Welds on both sides of the joint are shown by placing the weld symbol above and below the reference line.
[illustration: joint with arrow and reference line, showing fillet weld symbols above and below the reference line]
- Basic weld symbols describe the type of weld to be made. This symbol is a miniature drawing of the metal’s edge preparation prior to welding. The basic weld symbol is only part of the entire AWS welding symbol.
| Name | Symbol | Illustration |
|---|---|---|
| FILLET | [illustration: fillet weld triangle] | [photo: fillet weld cross-section on a plate] |
| PLUG | [illustration: rectangle] | [photo: plug weld on a plate] |
| SPOT | [illustration: circle] | [photo: spot welds on a plate] |
| SEAM | [illustration: circle with horizontal line through it] | [photo: seam weld on a plate] |
| BACKING | [illustration: half-oval] | [photo: backing weld cross-section] |
| MELT THRU | [illustration: solid half-oval] | [photo: melt-thru weld cross-section] |
| SURFACING | [illustration: two adjoining half-ovals] | [photo: surfacing weld on a plate] |
| FLANCE EDGE | [illustration: two curved edge lines] | [photo: flange edge weld] |
- The tail is added to the symbol only when special notes are required. A number or letter code used inside the tail direct the welder to special notes located elsewhere on the drawing. These notes may specify the heat treatment, welding process used, or other information not given on the welding symbol.
[illustration: reference line with arrow and a fillet weld symbol, with a tail]
Supplementary Symbols
[transcriber’s note: the three symbol tables below are printed side by side on the page]
| Name | Symbol |
|---|---|
| FILLET | [illustration: fillet weld triangle] |
| PLUG | [illustration: rectangle] |
| SPOT | [illustration: circle] |
| SEAM | [illustration: circle with horizontal line through it] |
| BACKING | [illustration: half-oval] |
| MELT THRU | [illustration: solid half-oval] |
| SURFACING | [illustration: two adjoining half-ovals] |
| FLANCE EDGE | [illustration: two curved edge lines] |
| Name | Symbol |
|---|---|
| WELD ALL ROUND | [illustration: circle] |
| FIELD WELD | [illustration: flag] |
| FLUSH | [illustration: horizontal line] |
| CONVEX | [illustration: convex arc] |
| CONCAVE | [illustration: concave arc] |
| Name | Symbol |
|---|---|
| SQUARE | [illustration: two vertical lines] |
| V | [illustration: V shape] |
| BEVEL | [illustration: slanted line] |
| U | [illustration: U shape] |
| J | [illustration: J shape] |
| FLARE V | [illustration: two flared curves] |
| FLARE BEVEL | [illustration: flared bevel curve] |
| FLANCE CORNER | [illustration: corner curve] |
Supplementary symbols can be placed above or below the basic symbol, or at the intersection of the reference line and the arrow. Dimensions and reference to specifications, or welding procedures may also be added.
- Weld all around is a circle drawn on the welding symbol, indicating that the described weld is to be made all around the part.
[illustration: reference line with arrow passing through a circle]
- Field weld symbol is a symbol added to the basic AWS welding symbol to indicate that a weld is to be made at the job site (“ in the field”), rather than in a fabricating shop.
[illustration: reference line with arrow and a flag symbol]
- Melt through is a complete joint penetration for a joint welded from one side and visible root reinforcement is produced.
[illustration: reference line with arrow and a solid half-oval symbol above the line]
- Backing symbol is an open rectangular box used in combination with a groove weld symbol located on the reference line indicating that locating materials is required on the opposite side control penetration.
[illustration: reference line with arrow and an open rectangle on the line]
- Spacer symbol is an open box that intersects the reference line, indicating that a spacer is placed between joint.
[illustration: reference line with arrow and an open rectangle crossing the line]
Contour and Finish Symbol
- Flush contour symbol is located on the same side as the symbol and indicates the weld should be approximately a flat plane with the surface.
[illustration: reference line with arrow, V-shaped weld symbol, and a flat horizontal line above it]
- Convex contour symbol is located on the side as the symbol and indicates that the weld should be raised or convex shape.
[illustration: reference line with arrow, V-shaped weld symbol, and a convex arc above it]
- Concave contour symbol is located on the same side as the symbol indicates that the weld should be concave shape.
[illustration: reference line with arrow, V-shaped weld symbol, and a concave arc above it]
- If the contour requires finishing, a finishing symbol will be used in conjunction with the contour symbol, a letter G indicate grinding, C indicate shipping, M indicate machining, and U indicate unspecified which local method should be used.
[illustration: reference line with arrow, V-shaped weld symbol, and a flat line above it with the letter C] Printed label: C
What’s More
Direction: Identify and Draw the described welding symbols.
- It is located on the same side as the symbol indicates that the weld should be concave shape.
- It is located on the same side as the symbol and indicates the weld should be approximately a flat plane with the surface.
- This symbol is an open box that intersects the reference line, indicating that a spacer is placed between joint.
- It is a circle drawn on the welding symbol, indicating that the described weld is to be made all around the part.
- A complete joint penetration for a joint welded from one side and visible root reinforcement is produced.
What I Have Learned
Identify the given symbols
| No. | Symbol |
|---|---|
| 1. | [illustration: reference line with arrow, V-shaped weld symbol, and a flat line above it with the letter C] |
| 2. | [illustration: reference line with arrow and an open rectangle on the line] |
| 3. | [illustration: reference line with arrow and a flag symbol] |
| 4. | [illustration: reference line with arrow and an open rectangle crossing the line] |
| 5. | [illustration: reference line with arrow, V-shaped weld symbol, and a flat line above it] |
What I Can Do
Directions: Suppose you were told to create a 4×4 Table with a high of 2ft what symbols are you going to use in sketching? Draw your sketch on a separate sheet of paper and List down at least Five (5) tools that you are going to use in creating this project.
[transcriber’s note: the printed page contains an empty answer box for this activity]
Post-Test
I. Multiple Choice
Which is not a part of ARC welding symbol
a. A reference line
b. An arrow
c. round
d. tailIt is a circle drawn on the welding symbol, indicating that the described weld is to be made all around the part.
a. Weld all round
b. Field weld
c. Field cut
d. CircleIt is located on the side as the symbol and indicates that the weld should be raised or convex shape.
a. Convex contour symbol
b. Concave contour symbol
c. All round
d. Site weldIt is a line connected to the arrow.
a. Reference line
b. arrow
c. Tail
d. Basic wield symbolIt indicates the position of the weld.
a. Reference line
b. arrow
c. Tail
d. Basic wield symbolIt is added to the symbol when a special note is required.
a. Reference line
b. Tail
c. Arrow
d. Basic wield symbolIt is an open box that intersects the reference line
a. Spacer
b. Backing
c. Flush contour
d. Concave contourWhat symbol is used if the contour requires finishing
a. Finishing symbol
b. Concave contour symbol
c. Convex contour symbol
d. SpacerIt is located on the same side as the symbol indicates that the weld should be concave shape
a. Finishing symbol
b. Concave contour symbol
c. Convex contour symbol
d. SpacerA symbol added to the basic AWS welding symbol to indicate that a weld is to be made at the job site.
a. Convex contour symbol
b. Field weld symbol
c. Finishing symbol
d. Weld all roundWhat does symbol F symbol represents?
a. Groove Angle
b. Finish
c. Length of Weld
d. Pitch of WeldAn open rectangular box used in combination with a groove weld symbol located on the reference line indicating that locating materials is required on the opposite side control penetration.
a. Backing symbol
b. Flush contour symbol
c. Buffing symbol
d. Box symbolWhat does symbol P represents?
a. Groove Angle
b. Finish
c. Length of Weld
d. Pitch of WeldWhat does symbol A represents?
a. Groove Angle
b. Finish
c. Length of Weld
d. Pitch of WeldWhat is the symbol for Site Flush Contour?
a. [illustration: open circle]
b. [illustration: short horizontal line]
c. [illustration: filled circle]
d. [illustration: arc]
Additional Activities
Analyze the given drawing, describe what is being represented by the symbols and enumerate the proper tools to be used and procedure for this welding sketch.
[illustration: welding sketch with a plain view (top) and two elevation views of fillet weld symbols, an isometric drawing of a fillet weld on a joint, and the desired weld between two plates]
PLAIN VIEW (TOP) DESIRED WELD ELEVATION ELEVATION OTHER SIDE FILLET WELDING SYMBOL ARROW SIDE FILLET WELDING SYMBOL
Answer Key
[transcriber’s note: this page is printed rotated 180 degrees; the answer key columns are transcribed in reading order]
Pretest
- a
- d
- b
- d
- c
- b
- d
- a
- c
- a
- a
- a
- b
- b
- a
Assessment
- c
- a
- a
- a
- b
- b
- a
- a
- b
- b
- b
- a
- d
- a
- b
What’s More
- Concave contour symbol + Drawing (Refer to module content)
- Flush contour symbol + Drawing (Refer to module content)
- Spacer + Drawing (Refer to module content)
- Weld all around + Drawing (Refer to module content)
- Melt through + Drawing (Refer to module content)
What I Have Learned
- Finishing symbol
- Backing symbol
- Field weld symbol
- Spacer
- Flush contour symbol
References
- Kennedy, G. A. (1982). Welding technology. Indianapolis: Bobbs-Merrill Educational Pub.
- Welding inspection technology: Workbook. (2008). Miami, FL: American Welding Society, Education Services.
- Jeffus, L. F., & Johnson, H. V. (2008). Welding principles and applications. Delmar
- Anderson, W., & School work helper Editorial Team. (n.d.). TECHNICAL DRAWING & ALPHABET OF LINE
- Weld Guru – Welding Guides & Resources Since 2006. (n.d.)
- American Welding Society. (n.d.)
- Rentapen. (n.d.). Retrieved June 16, 2020, from http://www.rentapen.com/
- Different Types of Welding Processes – Welding Helmet Pros. (n.d.). Retrieved June 16, 2020, from https://weldinghelmetpros.com/different-types-of-welding-processes
For inquiries or feedback, please write or call:
Department of Education – Bureau of Learning Resources (DepEd-BLR)
Ground Floor, Bonifacio Bldg., DepEd Complex Meralco Avenue, Pasig City, Philippines 1600
Telefax: (632) 8634-1072; 8634-1054; 8631-4985
Email Address: blr.lrqad@deped.gov.ph * blr.lrpd@deped.gov.ph
Leave a Reply