This is the Technology and Livelihood Education (TLE) Shielded Metal Arc Welding (SMAW) self-learning module for Grades 7 and 8, Quarter 1, Module 2: Perform Mensuration and Calculations (MC). It is an exploratory course that leads toward SMAW National Certificate Level II (NC II). It covers a common competency: basic measuring and calculating. After working through it, learners should be able to choose the right measuring tool for a task and measure the dimensions of an object in both inches and centimeters.
The module is the First Edition (2020), Alternative Delivery Mode. It was published by the Department of Education and printed by DepEd SOCCSKSARGEN Region. It was written by Ruby Joy S. Develos.
On this page 8 sections
What learners will learn
By the end of the lesson, learners are expected to:
- Select measuring instruments (TLE-IAAW7/8MC-0d1): use the right measuring tool for a specified task.
- Carry out measurements and calculations (TLE-IAAW7/8MC-0de-2): measure and calculate the dimensions of a specific object.
Why measurement matters in welding
The module explains that building and infrastructure projects depend on metal arc welding. Success in the trade depends on accurate measurements and calculations. A SMAW worker can do the job well only with proper knowledge of basic measuring.
Key ideas: systems and units of measurement
There are two systems of measurement:
- English System: started in England. It is also known as the U.S. customary system of measurement.
- Metric System: developed in France. It is also known as the S.I. (International Standard).
Units of linear measurement
| English | Metric |
|---|---|
| Yard (yd) | Meter (m) |
| Foot (ft or ‘) | Decimeter (dm), 1/10 meter |
| Inch (in or “) | Centimeter (cm), 1/100 meter |
| Millimeter (mm), 1/1000 meter |
Reading a ruler
- Inches: The inch is divided into segments called graduations. Each graduation stands for a proper fraction of an inch. An inch can be divided into 2, 4, 8, or 16 equal parts, so you read marks such as 1/16, 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, and 7/8.
- Centimeters and millimeters: Each centimeter on the metric scale is made up of 10 millimeters. So 1 cm is 10 mm, and 2 cm is 20 mm.
Key ideas: common measuring instruments
| Instrument | Use |
|---|---|
| Pull-push rule | Measuring long pieces of stock |
| Ruler (12-inch or one-foot rule) | Measuring short pieces of stock and taking simple measurements |
| Meter stick | A measuring device one meter long |
| Caliper | Measuring diameter, both inside and outside |
| Protractor | Measuring angles |
Taking dimensions with the right tool
- Length, width, and height of a metal stock: use a ruler, a pull-push rule, or a meter stick.
- Inside diameter of a cylindrical object: use a caliper.
- Outside diameter of a cylindrical object: use a caliper.
Activities in this module
- Pre-test (15 items): name the measuring instrument from a description or picture, then answer questions on the two measurement systems and on inch graduations.
- Activity 1: questions about measuring tools at home, common units used for metal products, and why correct measurements matter in metal arc welding.
- Activity 2: read the measurements marked on centimeter and inch rulers (10 items).
- Activity 3: name the two systems and their units, match each unit with its symbol, and identify ways of taking dimensions from pictures.
- Activity 4, Measure Me!: measure your table at home in centimeters and in inches. Then draw its layout with the measurements written on each side.
- Post-test (15 items): same format as the pre-test.
- Activity 5, Find Me!: a word search for six words related to units of measurement.
How to use this module
- Learners: Start with the pre-test to see what you already know. Then go through the parts in order, from What’s In to What I Can Do, and finish with the post-test. Write all answers in your activity notebook or on a separate sheet, not on the module. Answer keys are at the back, so check your work honestly after answering.
- Parents: For Activity 4, help your child find a measuring tool at home, such as a tape measure or ruler, to measure a table.
- Teachers and facilitators: The Notes to the Teacher ask learners to read the lessons carefully, take the learning activities, and apply what they learned to another activity or a real-life situation. The answer key covers the pre-test, post-test, and Activities 2, 3, and 5.
Frequently asked questions
What grade and quarter is this SMAW module for?
It is for TLE SMAW in Grades 7 and 8, Quarter 1, Module 2: Perform Mensuration and Calculations (MC).
What are the two systems of measurement in this module?
The English System started in England and is also called the U.S. customary system. The Metric System was developed in France and is also called the S.I. (International Standard).
Which tool measures the inside or outside diameter of a pipe or cylinder?
A caliper is used to measure both the inside and the outside diameter of a cylindrical object.
Does the module have an answer key?
Yes. The answer key at the back covers the pre-test, post-test, Activity 2, Activity 3, and the Activity 5 word search.
What are graduations on a ruler?
Graduations are the segments an inch is divided into. Each one stands for a fraction of an inch, and an inch can be divided into 2, 4, 8, or 16 equal parts.
Full text of the module
The text below is a transcription of the PDF above, as printed.
TLE (SMAW) Module 2: Perform Mensuration and Calculations (MC)
[illustration: group of students studying under a tree and at a table with a globe, a lamp, and a learner writing]
CO_Q1_TLE- -SMAW 7/8_ Module 2
TLE SMAW– Grade 7/8
Alternative Delivery Mode Module 2: Perform Mensuration and Calculations (MC). First Edition, 2020
Republic Act 8293, section 176 states that: No copyright shall subsist in any work of the Government of the Philippines. However, prior approval of the government agency or office wherein the work is created shall be necessary for exploitation of such work for profit. Such agency or office may, among other things, impose as a condition the payment of royalties.
Borrowed materials (i.e., songs, stories, poems, pictures, photos, brand names, trademarks, etc.) included in this module are owned by their respective copyright holders. Every effort has been exerted to locate and seek permission to use these materials from their respective copyright owners. The publisher and authors do not represent nor claim ownership over them.
Published by the Department of Education Secretary: Leonor Magtolis Briones Undersecretary: Diosdado M. San Antonio
Development Team of the Module
Writers: Ruby Joy S. Develos
Editors: Jose Joel B. Moso, Isidro L. Dagum, Jr.
Reviewers: Evelyn C. Frusa PhD, Grace J. Miravalles, Rolex H. Lotilla and Arvin Tejada
Illustrator: John Lester Escalera
Layout Artist: Janice G. Arroyo
Management Team: Allan G. Farnazo, CESO IV – Regional Director Gilbert B. Barrera – Chief, CLMD Arturo D. Tingson Jr. – REPS, LRMS Peter Van C. Ang-ug – REPS – ADM Coordinator Belen Fajemolin, Ph.D. – CID Chief Evelyn C. Frusa, Ph.D – EPS In Charge of LRMS Bernardita M. Villano – ADM Coordinator
Printed in the Philippines by Department of Education – SOCCSKSARGEN Region
Office Address: Regional Center, Brgy. Carpenter Hill, City of Koronadal Telefax: (083) 2288825/ (083) 2281893 E-mail Address: region12@deped.gov.ph
Introductory Message
This Self-Learning Module (SLM) is prepared so that you, our dear learners, can continue your studies and learn while at home. Activities, questions, directions, exercises, and discussions are carefully stated for you to understand each lesson.
Each SLM is composed of different parts. Each part shall guide you step-by- step as you discover and understand the lesson prepared for you.
Pre-test are provided to measure your prior knowledge on lessons in each SLM. This will tell you if you need to proceed on completing this module, or if you need to ask your facilitator or your teacher’s assistance for better understanding of the lesson. At the end of each module, you need to answer the post-test to self-check your learning. Answer keys are provided for each activity and test. We trust that you will be honest in using these.
In addition to the material in the main text, Notes to the Teachers are also provided to the facilitators and parents for strategies and reminders on how they can best help you on your home-based learning.
Please use this module with care. Do not put unnecessary marks on any part of this SLM. Use a separate sheet of paper in answering the exercises and tests. Read the instructions carefully before performing each task.
If you have any questions in using this SLM or any difficulty in answering the tasks in this module, do not hesitate to consult your teacher or facilitator.
Thank you.
What I Need to Know
Welcome to the world of Shielded Metal Arc Welding SMAW)! This Module is an exploratory course which leads you to Shielded Metal Arc Welding [SMAW] National Certificate Level II [NC II]. It covers common competencies for you to possess. These competencies include basic knowledge in mensuration and calculations.
Learning Objectives
At the end of the lesson, you are expected to do the following:
Select measuring instruments – TLE-IAAW7/8MC-0d1
Manipulate the measuring tool for a specified taskCarry out measurements and calculations – TLE-IAAW7/8MC-0de-2
Measure and calculate the dimensions of a specific object
What I Know
Pre-test
Let us determine how much you already know about selecting measuring instrument and carrying out measurement and calculations.
I. Direction: Identify the measuring instrument being shown or described in each item. Choose you answer on the table below. Write the letter of the correct answer in your activity notebook.
| A. Pull–push Rule | B. Ruler | C. Meter Stick | D. Caliper |
|---|
- It is used for measuring long pieces of stock.
- 12-inch/one-foot rule and it is used to take/make simple measurements.
- It is used for measuring short pieces of stock.
- It is used for measuring inside diameter.
- A measuring device which is one (1) meter in length.
- It is used for measuring outside diameter.
CO_Q1_TLE- -SMAW 7/8_ Module 2 (page 1)
- [illustration: pull-push rule]
- [illustration: ruler marked 0 to 12, labeled Inch]
- [illustration: meter stick]
- [illustration: caliper]
II. Direction: Read and analyze the following question. Write the letter of the correct answer in your activity notebook.
A system of measurement originated in England also known as the U.S. customary system of measurement.
a. Metric System c. Standard System
b. English System d. Measurement SystemIt was developed in France and also known as the S. I. (International Standard).
a. Metric System c. Standard System
b. English System d. Measurement SystemThe inch is divided into segments called ____________ .
a. System c. Standard
b. Measurement d. GraduationThe inch can be divided into 16, 8, 4 and 2, ____________ parts.
a. Equal c. More than
b. Not Equal d. Less thanWhich of the following is not included in English System?
a. Yard c. Feet
b. Meter d. Inch
CO_Q1_TLE- -SMAW 7/8_ Module 2 (page 2)
Lesson 2: Perform Mensuration and Calculations (MC)
Shielded metal arc welding is an important part of our lives. Building and infrastructural projects are dependent on metal arc welding and plays an important role in construction works.
The success of the industry depends mainly on the knowledge of accurate measurements and calculations. This module will guide you in performing measurements and calculations in relation to metal arc welding.
What’s In
Do you have some measuring tools at home? Can you identify those tools? I think you should know, because some of those tools are used in SMAW works by our worker in building construction trades. But, if not, you are going to explore here how to perform measurements and calculations.
Notes to the Teacher
- Read the lessons properly. These will guide you on what to do at the end of this module.
- Find out what you already know by taking the learning activities.
- Apply what you have learned in another activity or real life situation.
CO_Q1_TLE- -SMAW 7/8_ Module 2 (page 3)
System of Measurements
The two (2) systems of measurements are: The English and the Metric System. The English system originated in England also known as the U.S. customary system of measurement while the Metric System was developed in France and also known as the S. I. (International Standard).
I. (Unit of Measures) – Linear Measurement
| English | Metric |
|---|---|
| Yard (yd) | meter (m) |
| Foot (ft) / (‘) | decimeter (dm) 1/10 meter |
| Inch (in) / (“) | centimeter (cm) 1/ 100 meter |
| millimeter (mm) 1 /1000 meter |
II. Reading of Measurements
A. Reading the inch
The inch is divided into segments called graduations. Each graduation represents a measurement in the form of a proper fraction. The inch can be divided into 2, 4, 8 and 16, equal parts.
[chart: ruler scale; inch graduations as printed]
Top row (sixteenths): 1/16, 3/16, 5/16, 7/16, 9/16, 11/16, 13/16, 15/16 Bottom row (fractions of an inch): 1/8, 1/4, 3/8, 1/2, 5/8, 3/4 (printed as 1 8 1 4 3 8 1 2 5 8 1 7 8 in the source), 7/8, 1 in, 2 in
Note: The illustration is not the actual length of an inch.
B. Reading the centimeter and millimeter
[chart: ruler scale; centimeter and millimeter markings]
Labels printed: 1 2 3 4 5 6 7 8 9, 10 mm, 20 mm, 30 mm, 0, 1 cm, 2 cm
CO_Q1_TLE- -SMAW 7/8_ Module 2 (page 4)
What’s New
The following are common measuring instruments and their uses.
| Instrument | Illustration |
|---|---|
| 1. Pull-push rule – used for measuring long pieces of stock. | [illustration: pull-push rule] |
| 2. Ruler – used for measuring short pieces of stock. | [illustration: ruler marked 0 to 12, labeled Inch] |
| 3. Meter Stick – a measuring device which is one (1) meter in length. | [illustration: meter stick] |
| 4. Caliper – used for measuring the diameter. | [illustration: caliper] |
| 5. Protractor – a measuring instrument used to measure angles | [illustration: protractor] |
CO_Q1_TLE- -SMAW 7/8_ Module 2 (page 5)
What is It
The SMAW worker for metal arc welding can successfully do the job with the proper knowledge in basic measurements and calculations. Here are some of information on measuring the specific object using appropriate measuring instrument.
WAYS OF TAKING DIMENSION USING SPECIFIC MEASURING INSTRUMENT
| TASK | MEASURING INSTRUMENT/TOOL | ILLUSTRATION |
|---|---|---|
| 1. Measure the length of the stock/metal | RULER PULL-PUSH RULE RULER METER STICK | [illustration: rectangular stock with a tape measure extended along its length] |
| 2. Measure the width of the metal/stock | RULER PULL-PUSH RULE RULER METER STICK | [illustration: rectangular stock with a tape measure extended across its width] |
| 3. Measure the height of the metal/stock | RULER PULL-PUSH RULE RULER METER STICK | [illustration: rectangular stock with a tape measure extended along its height] |
| 4. Measure the inside diameter of a cylindrical object | CALIPER | [illustration: caliper measuring the inside diameter of a cylinder] |
| 5. Measure the outside diameter of a cylindrical object | CALIPER | [illustration: caliper measuring the outside diameter of a cylinder] |
Activity 1
Direction: Answer the following questions and write your answers in your activity notebook.
- Have you seen any measuring tools in your house? Give at least 3 examples
- What are the common units of measurement used for metal products?
- What is the importance of using correct measurements for metal arc welding?
What’s More
Activity 2
I. Direction: Write the correct measurements indicated below. Write your answer on your activity notebook.
[chart: ruler diagram; Activity 2 ruler with unlabeled measurement blanks]
Labels printed on the ruler: (1), (2), (3); 1 cm, 2 cm, 3 cm, 4 cm
[chart: ruler diagram; Activity 2 ruler with unlabeled measurement blanks, continued]
Labels printed on the ruler: (4), (5), (6); 1 in., 2 in., 3 in.
Labels printed on the ruler: (7), (8), (9), (10); 1 cm, 2 cm, 3 cm, 4 cm, 5 cm
_______ 6. _______
_______ 7. _______
_______ 8. _______
_______ 9. _______
_______ 10. ______
What I Have Learned
Activity 3
I. Direction: Enumerate the following.
1-2 – What are the two 2 systems of measurements
3-5 – Give at least 3 units of linear measurements in the English System
6-9 – Give at least 3 units of linear measurements in the Metric System
II. Direction: Match the unit with its equivalent symbol.
| Column A | Column B |
|---|---|
| 1. Centimeter | a) yd |
| 2. Millimeter | b) in |
| 3. Meter | c) cm |
[table continued from the previous page]
| Column A | Column B |
|---|---|
| 4. Yard | d) m |
| 5. Inch | e) mm |
| 6. Decimeter | f) dm |
| 7. Feet | g) ft |
III. Direction: Identify the different ways of taking dimensions as shown.
| No. | Illustration | Answer |
|---|---|---|
| 8. | [illustration: rectangular stock with a tape measure extended along its top edge] | _____________________ |
| 9. | [illustration: rectangular stock with a tape measure extended along its side] | _____________________ |
| 10. | [illustration: rectangular stock with a tape measure extended across its end] | _____________________ |
| 11. | [illustration: caliper measuring the outside diameter of a cylinder] | _____________________ |
What I Can Do
Activity 4: Measure Me!
Directions: You need to measure the dimension of your table in your house using the available tools you have. Apply the 2 measuring system: Metric System (use Centimeter), and English System (use Inch).
a. What is the equivalent of the table’s dimension in centimeter and in inch?
b. Draw the layout of your table and write the exact measurements (centimeter and inches) in each dimension?
[transcriber’s note: empty box for the learner’s drawing]
Assessment
Post-Test
Let us determine how much you have learned about selecting measuring instrument and carrying out measurement and calculations. Take this test.
I. Direction: Identify the measuring instrument being shown or described in each item. Choose your answer on the table below. Write the letter of the correct answer in your activity notebook.
A. Pull–push Rule B. Ruler C. Meter Stick D. Caliper
- It is used for measuring long pieces of stock.
- 12-inch/one-foot rule and it is used to take/make simple measurements.
- It is used for measuring short pieces of stock.
- It is used for measuring inside diameter.
- A measuring device which is one (1) meter in length.
- It is used for measuring outside diameter.
- [illustration: retractable pull-push rule with a tape housing]
- [illustration: 12-inch ruler marked in inches]
- [illustration: long metal meter stick]
- [illustration: caliper with a vernier scale]
II. Direction: Read and analyze the following question. Write the letter of the correct answer in you activity notebook.
- A system of measurement originated in England also known as the U.S. customary system of measurement.
a. Metric System c. Standard System
b. English System d. Measurement System
- It was developed in France and also known as the S. I. (International Standard).
a. Metric System c. Standard System
b. English System d. Measurement System
- The inch is divided into segments called _______.
a. System c. Standard
b. Measurement d. Graduation
- The inch can be divided into 2, 4, 6, 8 and 12 _______ parts.
a. Equal c. More than
b. Not Equal d. Less than
- Which of the following is not included in English System?
a. Yard c. Feet
b. Meter d. Inch
Additional Activities
Activity 5: Find Me!
Find the Six (6) words related to unit of measurement.
| A | S | F | E | E | T | T | Y | M | R | D | D |
|---|---|---|---|---|---|---|---|---|---|---|---|
| G | D | O | A | A | R | I | F | E | G | F | D |
| D | A | O | I | E | R | N | F | T | G | F | D |
| O | A | T | U | T | R | C | F | E | G | F | R |
| R | B | F | E | D | E | H | T | R | A | A | E |
| T | A | A | A | A | F | E | T | A | E | D | A |
| Y | B | B | E | D | E | S | T | T | T | F | E |
| T | B | B | D | D | F | Y | A | R | D | F | F |
| T | B | B | E | F | D | Q | E | G | E | E | E |
| C | E | N | T | M | E | T | E | R | G | H | F |
| Y | T | R | E | G | H | T | Y | Y | U | H | B |
Answer Key
Activity 3
- C
- E
- D
- A
- B
- F
- G
- Measure the length of the stock/metal
- Measure the width of the metal/stock
- Measure the outside diameter of a cylindrical object
- Measure the inside diameter of a cylindrical object
Activity 2
[transcriber’s note: the page is printed upside down and the answers are hard to read; the readings below are uncertain]
- 5mm/0.5cm
- D) cm [?]
- B5 cm [?]
- 0.75 in [?]
- 0.5 in [?]
- in [?]
- 7 mm [?]
- mm/0.5cm [?]
- mm [?]
- cm [?]
Pre-Test
- A
- B
- B
- D
- C
- D
- A
- B
- C
- D
- B
- A
- D
- A
- B
Activity 5
METER MILLIMETER INCHES CENTIMETER FOOT FEET
Post Test
- A
- B
- B
- D
- C
- D
- A
- B
- C
- D
- B
- A
- D
- A
- B
References
- CASTILLO, R. G., & SANTELICES, L. (n.d.). SMAW. K TO 12 TECHNOLOGY AND LIVELIHOOD EDUCATION.
- JEFFUS, L., & V., H. (n.d.). Welding Principles and Application.
- KENNEDY, G. A. (n.d.). Welding Technology, Second.
- SMAW: Shielded Metal Arc Welding. (2020, May 13). Retrieved June 03, 2020, from https://weldguru.com/smaw-welding/
- Welding inspection technology: Workbook. (2008). Miami, FL: American Welding Society, Education Services.
For inquiries or feedback, please write or call:
Department of Education – Bureau of Learning Resources (DepEd-BLR)
Ground Floor, Bonifacio Bldg., DepEd Complex Meralco Avenue, Pasig City, Philippines 1600
Telefax: (632) 8634-1072; 8634-1054; 8631-4985
Email Address: blr.lrqad@deped.gov.ph * blr.lrpd@deped.gov.ph
Leave a Reply